If you’ve ever stood on a factory floor watching a conveyor belt adjust its speed mid-run, or held a surgical tool that moves with precise, wobble-free rotation, you’ve probably interacted with linear rotary motion— and likely a component from linear-rotary.com, even if you didn’t know it. For over a decade, our small, tight-knit team of mechanical engineers and motion-control specialists has built our business on a simple promise: turn complex motion problems into reliable, off-the-shelf or custom solutions that don’t require you to rewrite your entire manufacturing or product design blueprint. This isn’t a big-box tech company spitting out generic parts; this is the work we’ve done side-by-side with automotive assembly lines, medical device makers, packaging equipment designers, and robotics startups for years, and today I’m walking through exactly what we offer, how it fits into your projects, and why we’re not the same as every other motion parts supplier out there. www.linear-rotary.com

First, let’s break down our core product line into categories that actually make sense for the teams that use them, because motion control isn’t one-size-fits-all. If you’re a design engineer, a maintenance manager, or a small business owner building a new prototype, you don’t care about jargon—you care about, “Will this part stop my assembly line from breaking at 2 a.m.?” or “Can this fit into my tight 12-square-inch space without custom machining?” That’s how we structure our offerings, no confusing catalog codes thrown around unless they matter.
Our top-selling product, and the one that put us on the map, is our line of integrated linear rotary actuators. A lot of suppliers sell linear actuators and rotary actuators as separate pieces, but integrating them cuts down on the number of parts you need to mount, reduces wear from misalignment, and saves you hours of assembly time. We make three main types of these, each for a different use case. The first are electric linear rotary actuators—these are for precision applications where you need consistent, repeatable movement. Think medical device manufacturing, where a surgical tool needs to rotate 180 degrees and move 2 inches up and down with an accuracy of ±0.01mm. We use high-grade stainless steel for the housing, and our internal bearings are rated for 10,000+ hours of continuous operation, which means less downtime for you. We don’t cut corners on the internal components, either; our lead screws are precision-ground, not rolled, so they don’t wear out unevenly over time.
The second type in this category are pneumatic linear rotary actuators. These are the workhorses for heavy-duty, high-volume applications, like packaging lines that flip a box from one conveyor to another. Pneumatic systems are cheap to run, fast, and don’t require electricity in many cases, which makes them perfect for factories where power access is limited or cost is a top priority. Our pneumatic units come with adjustable rotation stops and stroke lengths, so you can tweak them to match your line’s specific needs without ordering a custom part. We also offer corrosion-resistant versions for food and beverage processing, where washdowns are a daily requirement—no rust, no cross-contamination, just consistent movement.
The third are manual linear rotary actuators. These are for prototyping, small-batch production, or applications where you don’t need motorized power. A lot of hobbyists and small design teams use these to test a new product’s motion before investing in an electric system. We make them with aluminum housing for light weight, and the hand wheels have ergonomic grips that make turning smooth, no sticky spots or jolts. We even sell kits with mounting brackets and adapters, so you don’t have to source extra parts just to test your design.
Next up, we have standalone linear motion components—for when you don’t need a fully integrated actuator, just a part to fix or build your own system. This includes linear rails, lead screws, linear bearings, and ball screws, all precision-machined to industry standards, but we also offer custom machining if you have a specific design that doesn’t match our off-the-shelf parts. What sets our linear components apart is that we test every batch in-house before shipping. Last year, a customer came to us after a competitor’s ball screws were failing every 6 months in their assembly line; our engineers tested our equivalent model under identical load conditions, and it lasted 3 years. We don’t just source parts from third-party manufacturers and slap our logo on them—we work directly with our material suppliers to test every alloy for durability, which is why our customers come back. We also offer pre-assembled linear motion stages, which are ready to bolt into your machine, no extra machining needed. These are great for robotics platforms, where you need a precise linear slide to move a gripper.
Then there’s our line of rotary motion components, which range from servo motors and rotary encoders to gears and rotary tables. If you’re building a robotic arm, you need a rotary table that can hold a heavy load while rotating smoothly, right? Our rotary tables come in sizes from 100mm to 1000mm in diameter, with load capacities up to 10,000 lbs, and they’re designed for high-speed, high-precision applications like CNC machines or aerospace component assembly. We also offer hollow rotary tables, which let you run cables or hoses through the center, so you don’t have to route them around the table, reducing the risk of them getting caught and causing downtime. Our rotary encoders are another big seller—they track rotation position with extreme accuracy, which is critical for any automated system. We have both incremental encoders, which measure movement, and absolute encoders, which remember the exact position even if power cuts out, so you don’t have to re-calibrate your machine every time the power comes back on. That’s a huge time-saver for factories that experience frequent power fluctuations.
One of the parts of our business that I’m most proud of, though, is our custom motion solutions. A lot of suppliers will turn down a custom job if it’s less than 100 units, but we’re a small enough team that we can work with you on even a 10-unit prototype run, or a single custom part for a unique project. Last year, we worked with a startup that was building a new kind of prosthetic hand; they needed a linear rotary actuator that fit into a space of just 8 cubic inches, with enough torque to move a finger but light enough for a patient to wear. Our engineers worked with them for 3 months, testing different materials and bearing configurations, and ended up with a custom actuator that’s now used in over 2,000 prosthetic hands worldwide. We also work with large corporations, too—last quarter, we designed a set of linear motion stages for a major automotive company’s electric vehicle battery assembly line, where they needed to move delicate battery cells without damaging them. We adjusted the speed and force of the stages so that even a $10,000 battery cell would stay intact during assembly, which saved them millions in waste. Custom work isn’t just for big jobs; it’s for any team that has a unique motion problem that off-the-shelf parts can’t solve, and we’re equipped to handle that.
What a lot of our first-time customers don’t expect is that we don’t just sell parts—we offer technical support, too. We know that motion control can be overwhelming, especially if you’re not a mechanical engineer. Our team of application engineers is available to help you choose the right part for your project, troubleshoot problems if a part fails, or even help you design a motion system from scratch. I’ve had customers call me at 7 p.m. on a Friday because their assembly line went down over the weekend, and I’ve stayed on the phone with them for an hour to walk them through replacing a linear bearing, so they didn’t have to wait until Monday to get their line running again. That’s the kind of support you don’t get from a big online parts retailer, and it’s something we prioritize because we know how critical downtime is for any business.
We also offer value-added services, like integration of our parts into full motion systems, and refurbishment of old motion components. A lot of factories have aging machines with obsolete parts that are hard to find; instead of replacing the entire machine, we can refurbish the old linear rotary actuators or rotary tables, updating them with modern bearings or encoders, so you can extend the life of your equipment without the high cost of a new machine. That’s a big win for small businesses that can’t afford to upgrade their entire line every few years.
Now, let’s talk about who these products are for, because that’s a common question. Our customers range from small startups building prototype devices to Fortune 500 companies operating global manufacturing lines. If you’re a packaging engineer needing to build a new case sealer, our pneumatic linear rotary actuators will work for you. If you’re a medical device designer building a new insulin pump, our precise electric linear rotary actuators will meet your accuracy requirements. If you’re a robotics hobbyist building a custom robotic arm, our off-the-shelf rotary tables and encoders are perfect for your prototype. We also serve the aerospace, food and beverage, and agriculture industries, each with specialized versions of our parts to meet their unique standards—like food-grade lubricants for our washdown-ready pneumatic parts, or corrosion-resistant housings for outdoor agricultural equipment.

I want to be transparent about what we don’t offer, too, because honesty matters. We don’t sell generic, low-quality parts that break after a few months. Every part we ship has a 1-year warranty, and we stand behind it—if a part fails within the first year, we’ll replace it no questions asked. We also don’t offer overpriced parts that you can find cheaper online, because our focus is on quality and support, not undercutting competitors by cutting corners. We know that for many of our customers, downtime costs thousands of dollars an hour, so a slightly more expensive part that lasts 3 times longer and comes with support is a better investment than a cheap part that breaks every 6 months.
CNC Machining If you’re reading this, chances are you’re either working on a new project where you need a reliable motion component, or dealing with a broken part that’s costing you time and money. Whatever your need is—whether it’s an off-the-shelf linear actuator, a custom rotary table, or technical help designing your motion system—our team is here to help. We’ve worked on thousands of projects over the years, and we’re ready to bring that experience to yours. Don’t hesitate to reach out to start a conversation about your motion needs. We’re not just a parts supplier; we’re partners in keeping your equipment running smoothly.
References
- Standard for Precision Linear Motion Components, International Organization for Standardization (ISO 10360-2:2001)
- Pneumatic Actuator Durability Testing Protocol, National Fluid Power Association (NFPA T3.6.1:2019)
- Medical Device Motion Control Accuracy Requirements, U.S. Food and Drug Administration (FDA 21 CFR 820.30)
- Rotary Table Load Capacity and Tolerance Standards, Robotic Industries Association (RIA R15.06-2012)
- Custom Motion System Design Best Practices, Society of Manufacturing Engineers (SME MMOP:2021)
Sango Automation Limited
Sango Automation Limited is well-known as one of the leading cnc machining manufacturers and suppliers in China for 10 years. Our factory offers high quality cnc machining made in China with competitive price. Welcome to contact us for wholesale service.
Address: F3, Bld3, Huanrong Tech Park, No.1 Baima Xianfeng 2nd Road, Nancheng Street, Dongguan, Guangdong, 523106,China
E-mail: marketing@sango-automation.com
WebSite: https://www.sango-automation.com/